Sputtering Totally Explained

Everything about Sputtering totally explained

Sputtering is a process whereby atoms are ejected from a solid target material due to bombardment of the target by energetic ions. It is commonly used for thin-film deposition, etching and analytical techniques (see below).

Physics of sputtering

Physical sputtering is driven by momentum exchange between the ions and atoms in the material, due to collisions. The incident ions set off collision cascades in the target. When such cascades recoil and reach the target surface with an energy above the surface binding energy, an atom can be ejected. If the target is thin on an atomic scale the collision cascade can reach the back side of the target and atoms can escape the surface binding energy `in transmission'. The average number of atoms ejected from the target per incident ion is called the sputter yield and depends on the ion incident angle, the energy of the ion, the masses of the ion and target atoms, and the surface binding energy of atoms in the target. For a crystalline target the orientation of the crystal axes with respect to the target surface is relevant.
   The primary particles for the sputtering process can be supplied in a number of ways, for example by a plasma, an ion source, an accelerator or by a radioactive material emitting alpha particles.
   A model for describing sputtering in the cascade regime for amorphous flat targets is Thompson's analytical model . An algorithm that simulates sputtering based on a quantum mechanical treatment including electrons stripping at high energy is implemented in the program TRIM (www.srim.org) described in "Stopping and Range of Ions in Solids."
   A different mechanism of physical sputtering is heat spike sputtering. This may occur when the solid is dense enough, and the incoming ion heavy enough, that the collisions occur very close to each other. Then the binary collision approximation is no longer valid, but rather the collisional process should be understood as a many-body process. The dense collisions induce a heat spike (= thermal spike), which essentially melts the crystal locally. If the molten zone is close enough to a surface, large amounts of atoms may sputter due to flow of liquid to the surface and/or microexplosions. Heat spike sputtering is most important for heavy ions (say Xe or Au or cluster ions) with energies in the keV–MeV range bombarding dense but soft metals with a low melting point (Ag, Au, Pb, ...). The heat spike sputtering often increases nonlinearly with energy, and can for small cluster ions lead to dramatic sputtering yields per cluster of the order of 10000 .
   Physical sputtering has a well-defined minimum energy threshold which is equal to or larger than the ion energy at which the maximum energy transfer of the ion to a sample atom equals the binding energy of a surface atom. This threshold typically is somewhere in the range 10–100 eV. Preferential sputtering can occur at the start when a multicomponent solid target is bombarded and there's no solid state diffusion. If the energy transfer is more efficient to one of the target components, and/or it's less strongly bound to the solid, it'll sputter more efficiently than the other. If in an AB alloy the component A is sputtered preferentially, the surface of the solid will, during prolonged bombardment, become enriched in the B component thereby increasing the probability that B is sputtered such that the composition of the sputtered material will be AB.

Electronic sputtering

The term electronic sputtering can mean either sputtering induced by energetic electrons (for example in a transmission electron microscope), or sputtering due to very high-energy or highly charged heavy ions which lose energy to the solid mostly by electronic stopping power, where the electronic excitations cause sputtering.

Potential sputtering

In the case of multiply charged projectile ions a particular form of electronic sputtering can take place which has been termed potential sputtering. In these cases the potential energy stored in multiply charged ions (for example, the energy necessary to produce an ion of this charge state from its neutral atom) is liberated when the ions recombine during impact on a solid surface (formation of hollow atoms). This sputtering process is characterized by a strong dependence of the observed sputtering yields on the charge state of the impinging ion and can already take place at ion impact energies well below the physical sputtering threshold . Potential sputtering has only been observed for certain target species and requires a minimum potential energy .

Applications and phenomena

Film deposition

ť

Sputter deposition is a method of depositing thin films by sputtering, for example eroding, material from a "target," for example, SiO₂, which then deposits onto a "substrate," for example, a silicon wafer. Resputtering, in contrast, involves re-emission of the deposited material, for example, SiO₂, during the deposition also by ion bombardment.
Sputtered atoms ejected into the gas phase are not in their thermodynamic equilibrium state, and tend to deposit on all surfaces in the vacuum chamber. A substrate (such as a wafer) placed in the chamber will be coated with a thin film. Sputtering usually uses an argon plasma.

Etching

Removing atoms by sputtering with an inert gas is called `ion milling' or 'ion etching'.
Sputtering can also play a role in reactive ion etching (RIE), a plasma process carried out with chemically active ions and radicals, for which the sputtering yield may be enhanced significantly compared to pure physical sputtering. Reactive ions are frequently used in SIMS equipment to enhance the sputter rates. The mechanisms causing the sputtering enhancement are not always well understood, but for instance the case of fluorina etching of Si has been modelled well theoretically.
Sputtering which is observed to occur below the threshold energy of physical sputtering, is also often called chemical sputtering. The mechanisms behind such sputtering are not always well understood, and may be hard to distinguish from chemical etching. At elevated temperature chemical sputtering of carbon can be understood to be due to the incoming ions weakening bonds in the sample, which then desorb by thermal activation . The hydrogen-induced sputtering of carbon-based materials observed at low temperatures has been explained by H ions entering between C-C bonds and thus breaking them, a mechanism dubbed swift chemical sputtering.

For analysis

Another application of sputtering is to etch away the target material. One such example occurs in Secondary Ion Mass Spectroscopy (SIMS), where the target sample is sputtered at a constant rate. As the target is sputtered, the concentration and identity of sputtered atoms are measured using Mass Spectroscopy. In this way the composition of the target material can be determined and even extremely low concentrations (20 µg/kg) of impurities detected. Furthermore, because the sputtering continually etches deeper into the sample, concentration profiles as a function of depth can be measured.

In space

Sputtering is one of the forms of space weathering, a process that changes the physical and chemical properties of airless bodies, such as asteroids and our moon. It is also one of the possible ways that Mars has lost its atmosphere.

Further Information

Get more info on 'Sputtering'.

External Link Exchanges

Do you know how hard it is to get a link from a large encyclopaedia? Well we're different and will prove it. To get a link from us just add the following HTML to your site on a relevant page:

<a href="http://sputtering.totallyexplained.com">Sputtering Totally Explained</a>

Then simply click through this link from your web page. Our crawlers will verify your link, extract the title of your web page and instantly add a link back to it. If you like you can remove the words Totally Explained and embed the link in article text.
As long as your link remains in place, we'll keep our link to you right here. Please play fair - our crawlers are watching. Your site must be closely related to this one's topic. Any kind of spamming, dubious practises or removing the link will result in your link from us being dropped and, potentially, your whole site being banned.